AquaMix Seal & Finish Low Sheen, Gallon
Product Description
Aqua Mix Seal & Finish Low Sheen, gallon, is a specially formulated water-based blend of acrylic polymers that provides both a stain resistant surface seal and a durable low-sheen finish eliminating conventional two-step methods utilizing a sealer and finish. May also be used as a pre-grouting sealer. Allows moisture vapor transmission and is not affected by ultra-violet light.
Aqua Mix No VOC (Volatile Organic Compound) formulas help provide better indoor and outdoor air quality compared to similar traditional products. 100 grams of VOC's per liter of material.
Excellent Stain Resistance to household contaminants (CTI-072)
Excellent Mar Resistance
Matte sheen
For Use On: Unsealed, high porosity surfaces such as slate, quarry, saltillo, sandstone, terra cotta, cement pavers, and masonry. Effective for interior and exterior applications.
Limitations: Do not allow product to come in contact with any non-recommended surface.
Not recommended for use on glazed ceramic tile.
Not recommended for use around pools, showers or areas subject to standing water.
Keep surface clean and dry to reduce possibility of slip-fall accidents.
Expected Wear is up to 13 years: Will vary depending on hardness and texture of surface, type of area, surface wear, frequency and type of maintenance products used.
Expect more frequent application on exterior areas.
Weather conditions, harsh cleaning methods, and high-alkaline, acidic, or solvent-based cleaners will affect wear.
Instructions for Use:
Read entire label before using. Test in an inconspicuous area before treating entire surface. For new installations sealer can be applied as soon as 48 hours after grouting. Surface must be clean, dry, and free of existing sealers and coatings. Apply using a sponge or paint pad applicator. Avoid puddling. If 2 or more coats are applied, allow a minimum of 30 minutes drying time between coats. 2 hours after final coat conduct a test to determine if surface is completely sealed by applying water droplets to the surface. If water is absorbed, apply an additional coat. Wait 2 hours and repeat the test. Ready for surface traffic 6 hours after final coat. Keep area dry for at least 6 hours. Achieves a full cure in 24 hours.
For a high sheen finish on interior surfaces only, apply Aqua Mix Floor Shine & Hardener over Seal & Finish Low Sheen. Allow a minimum of 2 hours drying time before applying Aqua Mix finishes. Clean applicator tools with water after each use. May be reapplied as needed to surface that is clean and dry. Pre-grouting Application: Apply over clean stone or tile a minimum of 2 hours prior to grouting - follow application procedures above.
Coverage: Approximately 300 to 1,000 sq. ft. (30 m2 to 95 m2) per coat per gallon (3.8 L), depending on type, porosity and texture of surface, temperature, humidity, and method of application.
Maintenance: Aqua Mix Concentrated Stone & Tile Cleaner or AquaKleen or AquaShield is recommended for routine spray and wipe cleaning.
LEED Information: Aqua Mix LEED Contribution Product
Safety Data: Aqua Mix Seal & Finish Low Sheen MSDS
For Use On: Unsealed, high porosity surfaces such as slate, quarry, saltillo, sandstone, terra cotta, cement pavers, and masonry. Effective for interior and exterior applications.
Limitations:
Expected Wear is up to 13 years:
Instructions for Use:
Read entire label before using. Test in an inconspicuous area before treating entire surface. For new installations sealer can be applied as soon as 48 hours after grouting. Surface must be clean, dry, and free of existing sealers and coatings. Apply using a sponge or paint pad applicator. Avoid puddling. If 2 or more coats are applied, allow a minimum of 30 minutes drying time between coats. 2 hours after final coat conduct a test to determine if surface is completely sealed by applying water droplets to the surface. If water is absorbed, apply an additional coat. Wait 2 hours and repeat the test. Ready for surface traffic 6 hours after final coat. Keep area dry for at least 6 hours. Achieves a full cure in 24 hours.
For a high sheen finish on interior surfaces only, apply Aqua Mix Floor Shine & Hardener over Seal & Finish Low Sheen. Allow a minimum of 2 hours drying time before applying Aqua Mix finishes. Clean applicator tools with water after each use. May be reapplied as needed to surface that is clean and dry. Pre-grouting Application: Apply over clean stone or tile a minimum of 2 hours prior to grouting - follow application procedures above.
Coverage: Approximately 300 to 1,000 sq. ft. (30 m2 to 95 m2) per coat per gallon (3.8 L), depending on type, porosity and texture of surface, temperature, humidity, and method of application.
Maintenance: Aqua Mix Concentrated Stone & Tile Cleaner or AquaKleen or AquaShield is recommended for routine spray and wipe cleaning.
LEED Information: Aqua Mix LEED Contribution Product
Safety Data: Aqua Mix Seal & Finish Low Sheen MSDS
